|
|
Enquiry
|
|
Click on image for larger photo
|
Product Code:
BA-BH1AOZ2000A
ALUMINIUM RACING FLOOR JACK 2 TONNE.
MINIMUM LIFT95MM. MAXIMUM LIFT 482MM.
IDEAL FOR RACING - WEIGHT IS 24KG.
|
|
|
|
|
Please enter a valid quantity |
|
|
|
|
 |
|
|
|
BAHCO ALUMINIUM RACING TROLLEY FLOOR JACK 2 TONNE
LOW LIFT 95MM HIGH LIFT 482MM LIFTING WEIGHT 2000KG
- NYLON WHEELS
- TOOL TRAY FOR STORING NUTS, WASHERS
- COMPLY WITH AS/NZS 2615 2004
- SAFETY PRESSURE VALVE PREVENTING OVERLOADING
- LATERAL INSULATED HANDLES FOR EASY TRANSPORTATION
- 100% ALUMINIUM BODY ENSURES A FLEXIBLE AND LIGHTWEIGHT TROLLEY JACK
- RUBBER SADDLE INCLUDED PROTECTING ALL SURFACES AND PREVENTS SLIPPING
- USEFUL TRAY LOCATED AT THE BOTTOM OF THE HANDLE FOR STORAGE OF TOOLS, SCREWS AND NUTS
- SAFETY LOWERING VALVE ENSURES SAFE LOWERING EVEN AT MAXIMUM LOAD
- FOAM SLEEVE ON THE HANDLE TO PROTECT AGAINST BUMPING THE CAR BODY
- QUICK APPROACH TO THE LIFTING POINT THANKS TO THE DUAL PISTONS WHICH DECREASES THE NUMBER OF STROKES BY 50%
- DUST COVER THAT PROTECTS THE PISTONS AND SPRING REDUCING THE RISK OF DAMAGE CAUSED BY DUST AND DIRT
SAFETY PRECAUTIONS -
WARNING: FAILURE TO HEED THE FOLLOWING WARNINGS CAN RESULT IN PERSONAL INJURY AND/OR EQUIPMENT DAMAGE.THESE WARNINGS CANNOT COVER EVERY SITUATION, SO HAVE SAFETY FOREMOST IN YOUR MIND WHEN SETTING UP A JOB.
- READ, UNDERSTAND AND FOLLOW THE OPERATING INSTRUCTIONS AND THE ANSI B30.1 AND ASME PALD-1 SAFETY STANDARDS FOR JACKS. IF THE OPERATOR CANNOT READ ENGLISH, OPERATING INSTURCTIONS AND SAFETY PRECAUTIONS MUST BE READ AND DISCUSSED IN THE OPERATOR'S NATIVE LANGUAGE.
- WEAR EYE PROTECTION THAT MEETS THE REQUIREMENTS OF ANSI Z87.1 AND OSHA.
- INSPECT THE JACK BEFORE EACH USE; DO NOT USE THE JACK IF IT IS DAMAGED, ALTERED, OR IN POOR CONIDITION.
- TO PREVENT TIPPING, SET UP THE JACK ON A HARD, LEVEL SURFACE. SET VEHICLE PARKING BRAKE AND BLOCK TYRES.
- THE LOAD MUST NOT EXCEED THE RATED LIFTING CAPACITY OF THE JACK. LIFT ONLY DEAD WEIGHT.
- CENTER THE LOAD ON THE JACK SADDLE, BECAUSE OFF-CENTRE LOADS CAN DAMAGE SEALS AND CAUSE HYDRAULIC FAILURE.
- USE THE JACK FOR LIFTING PURPOSES ONLY. THIS JACK IS DESIGNED TO LIFT LOADS, NOT SUPPORT LOADS. IMMEDIATELY SUPPORT A LIFTED LOAD WITH JACK STANDS.
- STAY CLEAR OF LIFTED LOADS.
- USE ONLY APPROVED HYDRAULIC FLUID, SUCH AS CHEVRON AW HYDRAULIC OIL MV OR EQUIVALENT.
- THE JACK SHOULD BE USED ON HARD, LEVEL SURFACES
- THE WHEELS OF THE VEHICLE TO BE CHOCKED
- DO NOT PUT A PORTION OF YOUR BODY UNDER A VEHICLE SUPPORTED BY A JACK
- NO PERSON SHOULD REMAIN IN A VEHICLE THAT IS BEING JACKED
- DO NOT EXCEED THE WORKING LOAD LIMIT
OPERATING INSTRUCTIONS -
TO RAISE THE JACK, USE NARROW END OF JACK HANDLE TO TIGHTEN RELEASE VALVE CLOCKWISE (CW). INSERT HANDLE INTO SOCKET AND OPERATE PUMP. TO LOWER THE JACK, SLOWLY OPEN THE RELEASE VALVE KNOB BY TURNING IT COUNTERCLOCKWISE (CCW).
SHIPPING DIMENSIOS- 370MM X 810MM 190MM
|
View Complete Range:
|
WORKSHOP TOOLS > JACKS - FLOOR - NORMAL
WORKSHOP TOOLS > JACKS - FLOOR - ALUMINIUM
|
|
|
Video:
|
|
|
|
|
|