Solution Graphics
Shopping Cart

JACK AIR LONG RAM 8 TONNE CRANE

New and improved website Freight Free

Enquiry

JACK AIR LONG RAM 8 TONNE CRANE
Click on image for larger photo
Product Code: 44545

AIR HYDRAULIC RAM WITH HOSES & FITTINGS
8 TON CAP - TURN YOUR FLOOR & UTE CRANE
INTO AN AIR/MANUAL OPERATED UNIT
Border Image Border Image
Shop Price: $199.00
Web Price: $199.00  inc tax
 
Availability: In Stock
Quantity:
Weight: 14 KG
Border Image Border Image
AIR & MANUAL OPPERATED JACK LONG RAM 8 TON FOR SHOP CRANE

DESCRIPTION:
IDEAL FOR USE ON HYDRAULIC CRANES AND ENGINE HOISTS. BAKED ENAMEL FINISH.

CAN ALSO BE OPPERATED WITH NORMAL JACK HANDLE AS WELL AS AIR PUMP

DESCRIPTION:
IDEAL FOR USE ON HYDRAULIC CRANES AND ENGINE HOISTS. BAKED ENAMEL FINISH.

CAN ALSO BE OPPERATED WITH NORMAL JACK HANDLE AS WELL AS AIR PUMP

- AIR HYDRAULIC CAPACITY - 8000KG
- WITH CLEVIS BASE
- MAXIMUM RAM LENGTH BETWEEN HOLES 1140MM (APPROX)
- CLOSED HEIGHT: 645MM (APPROX)
- STROKE: 495MM
- BOTTOM YOKE WIDTH 26MM WITH 17MM HOLE ( CAN VARY??)
- SHAFT DIAMETER 28MM WITH A 17MM HOLE FOR MOUNTING
- AIR PRESSURE 80 TO 95 PSI


- NITTO AIR FITTING ON 1 METRE AIR HOSE

SAFETY PRECAUTIONS -

WARNING: FAILURE TO HEED THE FOLLOWING WARNINGS CAN RESULT IN PERSONAL INJURY AND/OR EQUIPMENT DAMAGE.THESE WARNINGS CANNOT COVER EVERY SITUATION, SO HAVE SAFETY FOREMOST IN YOUR MIND WHEN SETTING UP A JOB.

- READ, UNDERSTAND AND FOLLOW THE OPERATING INSTRUCTIONS AND THE ANSI B30.1 AND ASME PALD-1 SAFETY STANDARDS FOR JACKS. IF THE OPERATOR CANNOT READ ENGLISH, OPERATING INSTURCTIONS AND SAFETY PRECAUTIONS MUST BE READ AND DISCUSSED IN THE OPERATOR'S NATIVE LANGUAGE.
- WEAR EYE PROTECTION THAT MEETS THE REQUIREMENTS OF ANSI Z87.1 AND OSHA.
- INSPECT THE JACK BEFORE EACH USE; DO NOT USE THE JACK IF IT IS DAMAGED, ALTERED, OR IN POOR CONIDITION.
- TO PREVENT TIPPING, SET UP THE JACK ON A HARD, LEVEL SURFACE. SET VEHICLE PARKING BRAKE AND BLOCK TYRES.
- THE LOAD MUST NOT EXCEED THE RATED LIFTING CAPACITY OF THE JACK. LIFT ONLY DEAD WEIGHT.
- CENTER THE LOAD ON THE JACK SADDLE, BECAUSE OFF-CENTRE LOADS CAN DAMAGE SEALS AND CAUSE HYDRAULIC FAILURE.
- USE THE JACK FOR LIFTING PURPOSES ONLY. THIS JACK IS DESIGNED TO LIFT LOADS, NOT SUPPORT LOADS. IMMEDIATELY SUPPORT A LIFTED LOAD WITH JACK STANDS.
- STAY CLEAR OF LIFTED LOADS.
- USE ONLY APPROVED HYDRAULIC FLUID, SUCH AS CHEVRON AW HYDRAULIC OIL MV OR EQUIVALENT.
- THE JACK SHOULD BE USED ON HARD, LEVEL SURFACES
- THE WHEELS OF THE VEHICLE TO BE CHOCKED
- DO NOT PUT A PORTION OF YOUR BODY UNDER A VEHICLE SUPPORTED BY A JACK
- NO PERSON SHOULD REMAIN IN A VEHICLE THAT IS BEING JACKED
- DO NOT EXCEED THE WORKING LOAD LIMIT

OPERATING INSTRUCTIONS -

TO RAISE THE JACK, USE NARROW END OF JACK HANDLE TO TIGHTEN RELEASE VALVE CLOCKWISE (CW). INSERT HANDLE INTO SOCKET AND OPERATE PUMP. TO LOWER THE JACK, SLOWLY OPEN THE RELEASE VALVE KNOB BY TURNING IT COUNTERCLOCKWISE (CCW).

- READ, UNDERSTAND AND FOLLOW THE OPERATING INSTURCTIONS AND THE ANSI B30.1 AND ASME PALD-1 SAFETY STANDARDS FOR JACKS. IF THE OPERATOR CANNOT READ ENGLISH, OPERATING INSTURCTIONS AND SAFETY PRECAUTIONS MUST BE READ AND DISCUSSED IN THE OPERATOR'S NATIVE LANGUAGE.
- WEAR EYE PROTECTION THAT MEETS THE REQUIREMENTS OF ANSI Z87.1 AND OSHA.
- INSPECT THE JACK BEFORE EACH USE; DO NOT USE THE JACK IF IT IS DAMAGED, ALTERED, OR IN POOR CONIDITION.
- TO PREVENT TIPPING, SET UP THE JACK ON A HARD, LEVEL SURFACE. SET VEHICLE PARKING BRAKE AND BLOCK TYRES.
- THE LOAD MUST NOT EXCEED THE RATED LIFTING CAPACITY OF THE JACK. LIFT ONLY DEAD WEIGHT.
- CENTER THE LOAD ON THE JACK SADDLE, BECAUSE OFF-CENTRE LOADS CAN DAMAGE SEALS AND CAUSE HYDRAULIC FAILURE.
- USE THE JACK FOR LIFTING PURPOSES ONLY. THIS JACK IS DESIGNED TO LIFT LOADS, NOT SUPPORT LOADS. IMMEDIATELY SUPPORT A LIFTED LOAD WITH JACK STANDS.
- STAY CLEAR OF LIFTED LOADS.
- USE ONLY APPROVED HYDRAULIC FLUID, SUCH AS CHEVRON AW HYDRAULIC OIL MV OR EQUIVALENT.

OPERATING INSTRUCTIONS -

TO RAISE THE JACK, USE NARROW END OF JACK HANDLE TO TIGHTEN RELEASE VALVE CLOCKWISE (CW). INSERT HANDLE INTO SOCKET AND OPERATE PUMP. TO LOWER THE JACK, SLOWLY OPEN THE RELEASE VALVE KNOB BY TURNING IT COUNTERCLOCKWISE (CCW).

View Complete Range:

WORKSHOP EQUIPMENT > CRANES - UTE & TRUCK*
WORKSHOP EQUIPMENT > CRANES - FLOOR MOBILE*
WORKSHOP TOOLS > JACKS - AIR BOTTLE JACKS
LIFTING EQUIPMENT > CRANES - FLOOR MOBILE*
LIFTING EQUIPMENT > CRANES - UTE & TRUCK*
WORKSHOP TOOLS > JACKS - LONG RAM


Video:

 

© 2019 MARKINSON BUSINESS SOLUTIONS PTY LTD